Grand Willys Project
- robtus
- Senior Member
- Posts: 1108
- Joined: Wed Apr 27, 2011 9:54 pm
- Location: Moffat Beach SUNNY QLD
- Contact:
Re: Grand Willys Project
It looks BEAUTIFUL !!! Pity to camouflage all your hard work, but it is the right colour for cammo...
I never make the same mistake twice, I do it 5 or 6 times just to be sure !!!
Making progress, https://www.muston.com/public_html/34%2 ... _Limo.html
Making progress, https://www.muston.com/public_html/34%2 ... _Limo.html
-
- Posts: 419
- Joined: Wed Mar 25, 2015 4:50 am
- Location: Riverside Calif.
Re: Grand Willys Project
Beautiful color. Just the right amount of blue in it.
Dany
Dany
25 Hudson speedster project
29 Hudson coupe
36 Hudson 4dr sedan
36 Hudson LWB 4dr sedan
40 Hudson 2dr sedan
41 Hudson coupe
54 Hudson coupe
29 Hudson coupe
36 Hudson 4dr sedan
36 Hudson LWB 4dr sedan
40 Hudson 2dr sedan
41 Hudson coupe
54 Hudson coupe
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Grand Willys Project
Many thanks guys for all the comments.
Very pleased with the colour choice so glad I didn't change it. Got the right amount of mid tone not to loose colour in the shade and leave you wondering with it is.
Very pleased with the colour choice so glad I didn't change it. Got the right amount of mid tone not to loose colour in the shade and leave you wondering with it is.
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Grand Willys Project
Before putting it back on the chassis, I can finally run the donor Grand Cherokee under floor heat and isolation moulded mat.
There is also a firewall section and can see that I have to cut off the top section that used to go under the area of the donor cowl where the wipers and HVAC sat.
Only problem was that being right on the fold, it left an ugly edge along the top of the mat.
Used some pinch weld trim along the edge and that cleaned it up nicely. I had left all the mounting studs in place from the donor firewall and floor and placed the retainers back over them to hold it all in place.
There was also a factory pressed heat shield that sat above the exhaust system.
The pressed shield goes over the tunnel mat and fits perfectly.
We also put in the cab windows while it was easy to work around the cab. I put some rubber grease in the groove with along the cord as well as on the face of the lip that gets pulled over the window flange. Helps it pull over the flange when installing it.
Now it was time to roll the cab very carefully between the 32 Willys and the house to get it into the workshop.
Once along side the chassis, we attached the engine crane to the lifting rig I made that bolts to all the front seat mounts. It is angled back to be in the centre of balance of the cab.
Using plates between the crane and the rig with a single bolt allows me to tension the joint and stop it swinging around.
Can set it on an angle for instance and it stays there. Lisa is just keeping it steady and not holding any weight. We angled it up over the transmission as didn't have much head room under the panel door guide.
Not a lot of room between the back of the bell housing and the front of the bed floor, so had to go in straight.
It dropped straight over the mounts so the hard part is all done without damage.
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
- zuffen
- Senior Member
- Posts: 1934
- Joined: Fri Jan 28, 2011 7:45 pm
- Location: Sydney
Re: Grand Willys Project
Very impressive.
Never argue with an idiot, they will drag you down to their level and beat you with experience.
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Grand Willys Project
Video of the event.
Might be able to tell the stress level!
Might be able to tell the stress level!
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
- Sly Fox
- Senior Member
- Posts: 1925
- Joined: Sat Apr 24, 2010 7:10 pm
- Location: Castle Hill, NSW
Re: Grand Willys Project
The stress level sounded through the roof Marcus.
Lots of relief once the cab was landed, its looking better with every update.
Lots of relief once the cab was landed, its looking better with every update.
51 Dodge Custom & 63 EH Ute - Dare to be different
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Grand Willys Project
Hopefully that is the last of it, but I doubt it!
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
- 46OzHudson
- Posts: 283
- Joined: Thu Apr 07, 2016 11:41 am
- Location: WA
Re: Grand Willys Project
Nicely Done Marcus
I like how your using the heat guard, hopefully it makes it even more comfortable to drive
I like how your using the heat guard, hopefully it makes it even more comfortable to drive
"It's not perfect but it's progress"
-
- Posts: 103
- Joined: Thu Sep 23, 2010 2:12 am
- Location: Warrnambool
Re: Grand Willys Project
Well done Marcus, your wife and you make a good team. I can understand how you must have felt when it hit the carport, I have been there done that unfortunately. Cheers Pat
- hewey
- Old Hand
- Posts: 4928
- Joined: Fri Mar 10, 2006 12:11 am
- Location: Penrith, Sydney
Re: Grand Willys Project
The cab looks amazing in the sun, such a great colour choice. And glad to see you get mounted up with no damage, well apart from some nerves! Nice work.
Pariahs C.C.
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Grand Willys Project
Many thanks guys and it means more from other guys as they understand.
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
- Newbee
- Member
- Posts: 578
- Joined: Mon May 26, 2014 10:59 pm
- Location: YP of SA
Re: Grand Willys Project
Close shave with the beam and cab Marcus, looks great in the final colour, outstanding as usual.
Have fun putting it back together.
Regards Newbee
Have fun putting it back together.
Regards Newbee
- Gojeep
- Old Hand
- Posts: 7224
- Joined: Mon Jan 07, 2008 1:24 pm
- Location: Eastern Suburbs of Melbourne
- Contact:
Re: Grand Willys Project
Many thanks mate. Taking it easy and enjoying putting it together for the last time, in my ownership at least.
Marcus
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)
To try where there is little hope, is to risk failure.
Not to try at all, is to guarantee it!
____| \______\
|/¯\ |¯ |----O||||O
()_)-o-)¯¯()_)-o-)_)